Tempe Roofing Pros provides professional chimney & wall flashing in Tempe, AZ for residential and commercial properties across the East Valley. Very few Tempe houses have a masonry chimney, so the flashing work that actually keeps roofs dry here is at parapet walls, equipment curbs, and the two-story wall a lower roof runs into. The principle is identical and the details are not.
On a parapet, the coating over the foam is the flashing. It runs up the inside face, terminates in a bar with sealant, and is protected by counterflashing or a cap. When that roof leaks along a wall, the cause is almost always cracked coating at the termination, a bar fastened into failing stucco, or a cap with an open lap on the weather side. Terminations fail at the top edge, always.
Wall terminations where an addition meets the original house are the second common failure. Someone ran the low-slope system up the wall and stopped it under a bead of caulk, with no reglet cut, no counterflashing, and nothing mechanical holding the top edge down. That detail leaks the first time water sheets down the wall, and it is the one we rebuild most often. Caulk is not a substitute for a reglet.
Where there is a real chimney or a stucco chase, the work is conventional and unforgiving: a proper base flashing, step flashing up the sides of any sloped section, a cricket on the upslope face wide enough to divert water around rather than dam it, and counterflashing let into a cut reglet instead of surface-sealed. Crickets get skipped constantly and they are not optional.
Sealant is not a flashing and we will not sell it as one. A urethane or silicone bead is the last line of defence over a detail that is already correct, and using it as the whole detail is why so many wall junctions in this valley have been resealed four times by four contractors. We cut in the metal first, then seal. Order of operations is what separates a flashing from a smear.
Equipment curbs get the same treatment as any wall. Condenser and package unit curbs on a foam field are coated up and over, with flexible duct and conduit penetrations sealed at the curb rather than at the roof surface, since a penetration made out in the field is a hole somebody will eventually step on. Keeping penetrations at the curb rather than in the field is worth a small amount of extra sheet metal.
Our licensed and insured team brings the right materials and equipment to every job — sprayed polyurethane foam at three-pound density, acrylic elastomeric coating meeting ASTM D6083, high-solids silicone topcoat, dry film thickness measured in mils, electronic capacitance moisture survey, dusk infrared thermography scan — and backs the work with a written workmanship warranty. We serve Tempe and nearby communities including Mesa, Chandler, Gilbert, Scottsdale.
What We Handle
Everything our chimney & wall flashing in Tempe covers
One crew, one point of contact, and the full range of chimney & wall flashing work in Tempe, AZ. If it is on this list we do it in house rather than handing it to a subcontractor:
- chimney flashing repair
- flashing on roof
- roof to wall flashing
- parapet wall flashing
- counterflashing reglet
- step flashing repair
- chimney cricket
- termination bar sealant
- equipment curb flashing
- wall termination leak
- flashing repair Tempe
Not sure which one describes your situation? Describe it in plain words and we will sort it out — or browse the rest of our Tempe services.
Materials, equipment and how we do chimney & wall flashing
The difference between chimney & wall flashing that lasts and chimney & wall flashing that gets redone in three years is almost always preparation and materials, not the finish you see on day one. We work with sprayed polyurethane foam at three-pound density, acrylic elastomeric coating meeting ASTM D6083, high-solids silicone topcoat, dry film thickness measured in mils, spec them to the job instead of to the invoice, and write the material grades into the free estimate so you know exactly what you are buying.
Every Tempe job runs the same way: site walk and measurements, written scope and fixed price, protection of the surrounding area, then the work itself with a daily clean-up. Years of roofing work in the East Valley means we have already met whatever your property is going to throw at us — awkward access, older construction, an HOA with opinions.
Where we do chimney & wall flashing outside Tempe
Tempe Roofing Pros covers Tempe and the surrounding communities of the East Valley. Crews run out to the same nearby cities every week, so an out-of-town job does not mean an out-of-town price.
- Chimney & Wall Flashing in Mesa, AZ — Maricopa County, population 504,258
- Chimney & Wall Flashing in Chandler, AZ — Maricopa County, population 275,987
- Chimney & Wall Flashing in Gilbert, AZ — Maricopa County, population 267,918
- Chimney & Wall Flashing in Scottsdale, AZ — Maricopa County, population 241,361
- Chimney & Wall Flashing in Phoenix, AZ — Maricopa County, population 1,608,139
- Chimney & Wall Flashing in Queen Creek, AZ — Maricopa County, population 59,519
Start on the Tempe Roofing Pros homepage for a free estimate, or call (844) 511-2320 and describe the job.
Why Tempe Chooses Tempe Roofing Pros
- ✓Every coating proposal names the product, its ASTM standard and the dry film thickness in mils, never a gallon count
- ✓Core cuts and an electronic moisture scan before a recoat is priced, because coating over wet foam buys nothing
- ✓Thickness readings taken at the same marked points every visit, so you see a wear rate instead of one afternoon's opinion
- ✓Ponding corrected by building slope in foam rather than patched with more material at the low spots
The standards behind chimney & wall flashing
Quality here is not a matter of opinion — it is written down. The chimney & wall flashing work we do in Tempe follows published industry standards: NRCA publishes the Roofing Manual, the industry's reference for details and slope minimums, and Asphalt Roofing Manufacturers Association sets the shingle application and ventilation guidance the warranties reference. If a contractor cannot tell you which standard a detail comes from, that is worth asking about before you sign.
Every chimney & wall flashing project in Tempe gets the same attention, whether it is a single room or a full commercial job. We show up on schedule, keep the site clean, and stand behind the work — the estimate is free and there is no pressure.
Ready to get started? Call (844) 511-2320 for a free chimney & wall flashing free estimate in Tempe, or request a quote and we'll get right back to you.